Often, an Architect, Civil Engineer, General and flooring contractors are well versed in the specification and installation practices of non static control flooring systems. However, expertise is required in developing ESD safe protocols which reflect ANSI level standards for the validation of both static dissipative and conductive flooring. RMV will recommend and perform evaluations for grounding, resistance to a groundable point, point to point resistance, resistance in combination with a person and voltage in combination with a person. In addition, RMV can map the floor's performance to various voltage levels.

Static Control flooring can represent a capital expenditure so it is important to outline clear-cut benchmarks for the flooring contractor and installation company. RMV can specify requirements and evaluate a flooring company's product before and after installation.

Testing to New ANSI/ESD S541-2003 Standard for:

Packaging and Materials

• ESD S20.20 PreCertification of Facilities and Cleanrooms to ANSI/ESD S20.20-2007 [IEC-61340-5-1]
• Surface Resistance ANSI/ESD STM11.11-2006
• 2-Point Resistance ANSI/ESD STM11.13-2004
• SURFACE RESISTANCE OF STATIC DISSIPATIVE MATERIALS
  Surface Resistivity ASTM-D257-2007
• DC RESISTANCE OR CONDUCTANCE OF INSULATING MATERIALS
• Volume Resistivity ASTM D991-2005
• VOLUME RESISTIVITY OF ELECTRICALLY CONDUCTIVE AND ANTISTATIC PRODUCTS
• Volume Resistance ANSI/ESD STM11.12-2007
• ELECTRICALLY CONDUCTIVE HOMOGENEOUS MATERIALS
• Dr. Kolyer High Voltage Discharge Test
• SHIELDING FOR PACKAGING
• Capacitive Probe Test
• SEMI® E-78 Evaluation Compliance

ANSI/ESD STM11.31-2006 SHIELDING FOR BAGS

• BELLCORE RUB TESTER
• TRIBOCHARGE GENERATION
• Static Decay EIA 541-1988
• Tribo-charging and Charge Generation
• Non Contact Voltage Measurements
• FARADAY Cup Measurements Simulator Discharges and others...

ADDITIONAL TESTING SERVICES INCLUDES

• ANSI/ESD S1.1-2006 Wrist Straps
• ANSI/ESD STM2.1-1997 Garments
• ANSI/ESD STM3.1-2006 Ionization
• ESD SP3.3-2000 Periodic Verification of Air Ionizers
• ANSI/ESD S4.1-2006 Worksurface–Resistance Measurements
• ANSI/ESD STM4.2-2006 ESD Protective Worksurfaces–Charge Dissipation Characteristics
• ANSI/ESD S6.1-2005 Grounding
• ANSI/ESD S7.1-2005 Resistive Characterization of Materials–Floor Materials
• ANSI/ESD STM 9.1-2001 Footwear–Resistive Characterization
• ESD SP9.2-2003 Footwear–Foot Grounders Resistive Characterization
• ANSI/ESD STM12.1-2006 Seating–Resistive Measurement
• ANSI/ESD STM 13.1-2000 [WIP for 2008] Electrical Soldering/Desoldering Hand Tools
• ANSI/ESD SP15.1-2005 In-Use Resistance Testing of Gloves and Finger Cots
• ANSI/ESD STM97.1-2006 Floor Materials and Footwear–Resistance
• Measurement in Combination with a Person
• ANSI/ESD STM97.2-2006 Floor Materials and Footwear– Voltage Measurement in Combination with a Person

MILITARY HANDBOOK TESTING SERVICES

• IEC Standards Testing
• EIA Standards Testing
• JEDEC Standards Testing
• Following your Company Procedures

RMV Electrostatic Decay Testing Note:

MIL-STD-3010A
18 August 2005
SUPERSEDING
MIL-STD-3010
30 December 2002

This document, MIL-STD-3010, dated 30 December 2002, supersedes FED-STD-101C. This standard provides test methods to evaluate materials used in military packaging.

MIL-STD-3010
30 December 2002
SUPERSEDING
FED-STD-101C
13 March 1980

EQUIPMENT ESD FIELD & EVENT DETECTION TO THE VOLT

Materials Test & Evaluation (MT&E)

• Emerging materials (CNT, IDP, ICP) test and evaluation for ESD analysis
• In premixed applications of multiwall carbon nanotube composites (CNT), test and evaluation of the electrical conductivity of the plastic material
• Specialized Applications ESD testing
• Development of unique fixturing for small profile test methodologies
• Testing will determine the surface resistance, tribocharging, decay and other test methods that measure conductivity of protective coatings for aerospace materials.

MT&E Evaluation of Materials & Processing (M&P)

• Coatings, Adhesives, Laminates, Paint Technologies.
• Analysis of ESD properties; M&P evaluations and analysis.
• Materials characterizations (ESD analysis), ESD assessments of select M&P for applicability to structural components; development of M&P solutions to ESD problems with material structures.
• Assist customers in identifying M&P problems and recommend solutions; perform M&P evaluations on structural components; develop & evaluate Electrostatic Discharge (ESD) protection methods.